Garage floors
The floor most Valley homeowners ask for.
- Full-flake polyaspartic system
- Diamond-ground prep, never acid etching
- Most garages finished in about a day
- Park on it in roughly 24 to 48 hours
Concrete coatings · Queen Creek, Arizona
Floors that take the heat.
Arizona's finest garage floors. Full-flake polyaspartic coatings for Queen Creek and the Valley, diamond ground, crack repaired and sealed under a UV-stable topcoat that shrugs off hot tires and July sun. Installed in about a day.
Scroll
Full flakeBroadcast to refusal
About 1 dayTypical garage install
24 to 48 hrsThen park on it
20 citiesValley wide, ~50 miles
Services
Built for the concrete under your life.
TruForce Epoxy installs full-flake polyaspartic coatings in Queen Creek, the East Valley and greater Phoenix. Every floor is diamond ground, crack repaired and sealed with a UV-stable topcoat that resists hot tires, oil and Arizona sun.
Patios & pool decks
Outdoor concrete takes sun all day, so the topcoat matters most here.
- UV-stable topcoat that will not yellow
- Anti-slip texture for wet areas
- Covered and uncovered patios, entries, walkways
- Lighter blends that stay cooler underfoot
Commercial & shops
Floors for forklifts, tools, fluids and foot traffic.
- Shops, warehouses and showrooms
- Chemical- and abrasion-resistant systems
- Scheduling around your hours
- One continuous surface that sweeps clean
Concrete repair & prep
A coating is only as good as the slab under it.
- Crack, spall and pitting repair
- Diamond grinding to open the surface
- Old coating removal
- Moisture checks before coating
Process
Your garage, transformed in five steps.
The same order on every job. Most garages go from bare slab to sealed floor in about a day, with walk-on in hours and parking in roughly 24 to 48 hours.
- 01
Grind & profile
Diamond grinding opens the slab for a mechanical bond. No acid etching, ever.
- 02
Repair
Cracks, spalls and pits are cleaned out, filled and ground flush.
- 03
Base coat
A pigmented base coat goes down over the whole floor, and the stem walls if you want them.
- 04
Full flake broadcast
Vinyl flake is thrown to refusal until no base shows, then scraped and swept smooth.
- 05
Polyaspartic seal
A clear, UV-stable polyaspartic topcoat locks it in. Walk on it in hours.
Before & after
Same slab. One day later.
Every garage starts as bare, dusty concrete. Drag the handle to see what a full-flake polyaspartic floor does to it, then try a blend.
Before
After · Shoreline
Drag to reveal the finished floor.
- Diamond ground, never acid etched, so the coating bonds to the concrete itself.
- Flake broadcast to refusal: no base coat shows through.
- Polyaspartic topcoat that holds its color in the sun and resists hot-tire pickup.
Sample blends, rendered on screen. Confirm your pick with a physical flake sample before install day.
Color samples
Twelve blends for desert light.
From Shoreline beige to Raven black, with solid colors and custom blends on request. Here are eight of the twelve.
Shorelinewarm beige with soft brown
Stone Hengecool greys and white
Coyoteearthy tan with charcoal
Dominocrisp black and white
Cometsteel blue and grey
Outbackwarm tan and leather brown
Ravendeep black with light flecks
Creek Bedriver stone on a sandy base
Why TruForce
Premium materials. Expert hands.
One system, installed the same careful way on every job, by a crew that lives where you do.
Queen Creek based
We are a short drive from every East Valley neighborhood, so site visits and early-morning starts are easy to schedule.
Full flake, every time
Flake is broadcast to refusal and sealed under polyaspartic. No thin, partial or "light flake" floors.
Grind, never etch
Diamond grinding gives the coating something to grip. Acid etching does not, and it is where peeling starts.
Built for the Valley
UV-stable chemistry chosen for open garage doors, hot tires and 115-degree summers.
Gallery
Up close with the flake.
Quarter-inch and eighth-inch chip, sealed under a clear polyaspartic gloss.
The Grind, our blog
Prep, pour, polyaspartic.
Straight answers about coatings in Arizona heat, what moves an estimate, and how to keep a flake floor looking new.
Polyaspartic vs Epoxy Garage Floors in Arizona Heat
How UV, 110-degree summers and hot tires change the coating choice for a Valley garage, and when epoxy still makes sense.
Read articleWhat Affects Garage Floor Coating Cost in the East Valley
Square footage, slab condition, cracks, moisture, flake size, stem walls and add-ons: what moves an estimate and why.
Read articleHow to Clean a Flake Garage Floor
A routine that keeps a full-flake polyaspartic floor looking new, plus fixes for tire marks, oil and Arizona hard water spots.
Read article
Queen Creek, AZ
About
Queen Creek based. Valley wide.
TruForce Epoxy creates Arizona's finest garage floors with premium materials and expert craftsmanship. We install one system we trust, a full-flake polyaspartic floor over diamond-ground concrete, and we install it the same careful way whether the garage is in Queen Creek or across the Valley.
Our service area runs about 50 miles out from Queen Creek: the East Valley, Phoenix, Scottsdale, the West Valley and Pinal County.
Queen Creek
Our home base. New-build garages in Hastings Farms, Harvest and Barney Farms are often coated soon after move-in, before years of oil and tire stains soak into the slab.
San Tan Valley
In Johnson Ranch, Encanterra and Pecan Creek, garages double as home gyms, workshops and golf-cart parking, so we plan the floor around how you use the space.
Gilbert
From Agritopia to Power Ranch, Morrison Ranch and Val Vista Lakes, a west-facing Gilbert garage takes full afternoon sun every time the door opens. That is where a UV-stable topcoat pays off.
Mesa
Mesa slabs range from new pours in Eastmark to decades-old concrete near Red Mountain and Las Sendas. Older floors usually need more crack and spall repair before coating.
Chandler
Three-car and tandem garages are common in Ocotillo and Fulton Ranch. One continuous flake floor across the whole space reads cleaner than patched or partial coatings.
Phoenix
From Arcadia bungalows to Desert Ridge, Phoenix garages vary widely in age and condition. Prep is matched to each slab before any coating goes down.
Scottsdale
In McCormick Ranch and DC Ranch, many garages hold collector cars or golf carts. Flake size and color blend are where most Scottsdale homeowners spend their decision time.
Glendale
West Valley garages get the same diamond-grind prep and polyaspartic system as our East Valley jobs, scheduled as part of our Valley-wide service area.
Also serving
- Tempe
- Ahwatukee
- Paradise Valley
- Fountain Hills
- Apache Junction
- Gold Canyon
- Sun Lakes
- Florence
- Coolidge
- Maricopa
- Casa Grande
- Laveen
FAQ
Answers, before you ask.
The questions Valley homeowners ask most before booking a floor.
How long does a garage floor coating take to install?
Most two- and three-car garages are completed in about one day with a polyaspartic system. You can typically walk on the floor within a few hours and park on it in roughly 24 to 48 hours, depending on temperature and the products used.
Will a polyaspartic garage floor yellow in the Arizona sun?
No. Polyaspartic topcoats are aliphatic, which makes them UV stable, so they hold their color when the garage door is open to direct sun. Many standard epoxies are aromatic and can amber or yellow with UV exposure, which is why they are usually covered with a UV-stable topcoat.
Are cracks repaired before the floor is coated?
Yes. After diamond grinding, cracks, spalls and pitting are cleaned out, filled and ground flush so they do not show through the finish. A crack can reappear if the slab keeps moving, and a full-flake broadcast helps disguise hairline lines.
Is a flake garage floor slippery?
A full-broadcast flake floor has a light texture from the chips, which gives more grip than smooth sealed concrete. The texture can be increased with an anti-slip additive in the topcoat, which is worth asking about for patios, pool decks and garages that see water.
How do you clean a coated garage floor?
Sweep or dust mop weekly, then wash with warm water and a pH-neutral cleaner using a soft deck brush or microfiber mop. Squeegee the floor dry to prevent hard water spots, and avoid acidic, citrus or vinegar cleaners.
How much does a garage floor coating cost?
Cost depends on square footage, slab condition, crack and moisture repair, flake size and add-ons such as stem walls. TruForce Epoxy gives free estimates so the price reflects your actual floor rather than a per-foot guess.
Something else? Call or text (480) 853-3322.
Get a quote
Get a real number in about a minute.
Three quick questions: your space, your colors, and how to reach you. Your quote comes to your inbox, and we confirm the number on site before any work starts.
Rather talk? Call or text any time.
(480) 853-3322- Your spaceGarage, patio or shop, how big it is, and which city.
- Your colorsPick one of twelve flake blends, or ask us to bring samples.
- How to reach youName, email and phone. The quote lands in your inbox.